Search This Blog

Showing posts with label - 3ch trainer. Show all posts
Showing posts with label - 3ch trainer. Show all posts

Saturday, 19 December 2015

Simple 3 channel trainer

This design was inspired by a friend who wanted to take one of my "retired" planes to learn how to fly. So I gathered bits and pieces together and tried to come up with an easy to fly, crash proof trainer.

It only has rudder elevator and throttle, no ailerons. I wanted it to be as light as possible for slow and easy flight with a big energy absorbing nose and a tough fuselage.



The fuselage was shaped from a 50 x 100 x 370 block of XPS insulation foam and the tail planes are 8mm panels of the same foam. The boom is a Skyshark P4X 7.6mm tube.

The hotwire-cut 170mm clark y wing comes from rescued sections of the drowned Fokker (which now has new wings) Three x 360mm sections were glued together with the tips each raised 120mm. No spars are needed to hold the polyhedral due to the tape covering and large join surface area for gluing.


The nose is soft packing foam covered with tape and completely encases the 1300mAh Lipo battery.

The motor is the original Bixler 2, servos are cheap 9g HXTs, and it has a Plush 18A ESC and HobbyKing 3 channel receiver.

All up weight with the battery adds up to 550g, giving a slow continuous cruising flight time of over 30min.

This plane is very smooth and stable and with correct trim will fly hands off.

At this stage the nose, fuse and wings are almost bullet proof, but the tail planes are a bit too delicate. Thinner sheets of XPS foam are quite brittle so some kind of reinforcing is needed.  Both the elevator and rudder have cracked during the test flights so I have added a 0.5 x 3mm CF spars.

Might be better to use depron or corflute for the tail.


Dimensions



Flight video - motor slope soaring

Build video


UPDATE 30 March 2016 

After some tough flight testing by my dedicated student test pilot it became apparent that this tail
design was not crash proof enough.

So here is the new tougher tail design made from depron. The tail to boom join has extra foam fillets either side for more gluing area and to raise the elevator a little.

The new wing has more area and less polyhedral for smoother flight.


Update overview video

Tail build video

Dimensions for the updated tail design






MATERIALS
New Stuff iron-on film - EZload laminate - http://www.neopostonline.com.au/lamination/ez-load-roll-film

BUILD VIDEOS


Friday, 13 June 2014

Pusher with polyhedral

I have never tried a 3 channel rudder elevator throttle plane so thought I'd give it a go using the orange slim wing and pusher fuselage.

RET planes need some wing dihedral to enable turns due to the lack of ailerons.

I fixed the ailerons in place and removed the servos. This simplifies the plane greatly, the wing is just a wing, no servos or wires, apart from rudder and elevator.

The CF spar was removed and a bent 200mm x 10mm diam ali tube inserted to set the dihedral. The wing extensions were hot glued in place at the desired polyhedral angle. The wing seems to be strong enough without a CF spar.

I increased the rudder area, but after the maiden reduced the throws for smoother control.

The 1500mm x 200mm wing and flying weight of 630g gives a wing loading of about 21 g/sq dm (7oz/sq ft) which is great for gliding and slow flying.

This plane is a delight to fly, so slow and steady. If I had started with something like this the learning process would have been much quicker. I can trim it to fly hands off in big lazy circles and it takes care of itself.



Wingspan - 1.5m (59")
Chord - 200mm (8")
Elevator servo - TGY 900 9g
Rudder servo - TGY 500 5g (stronger servo might be safer)
Motor - Turnigy 2822/14 1450kV
Prop - 7 x 4.5"
Airframe weight - 520g
Flying weight - 630g with 1300mAh LiPo (gives 20 min slow flying)

Sketchup Plans