Search This Blog

Friday, 13 June 2014

Pusher with polyhedral

I have never tried a 3 channel rudder elevator throttle plane so thought I'd give it a go using the orange slim wing and pusher fuselage.

RET planes need some wing dihedral to enable turns due to the lack of ailerons.

I fixed the ailerons in place and removed the servos. This simplifies the plane greatly, the wing is just a wing, no servos or wires, apart from rudder and elevator.

The CF spar was removed and a bent 200mm x 10mm diam ali tube inserted to set the dihedral. The wing extensions were hot glued in place at the desired polyhedral angle. The wing seems to be strong enough without a CF spar.

I increased the rudder area, but after the maiden reduced the throws for smoother control.

The 1500mm x 200mm wing and flying weight of 630g gives a wing loading of about 21 g/sq dm (7oz/sq ft) which is great for gliding and slow flying.

This plane is a delight to fly, so slow and steady. If I had started with something like this the learning process would have been much quicker. I can trim it to fly hands off in big lazy circles and it takes care of itself.



Wingspan - 1.5m (59")
Chord - 200mm (8")
Elevator servo - TGY 900 9g
Rudder servo - TGY 500 5g (stronger servo might be safer)
Motor - Turnigy 2822/14 1450kV
Prop - 7 x 4.5"
Airframe weight - 520g
Flying weight - 630g with 1300mAh LiPo (gives 20 min slow flying)

Sketchup Plans











Friday, 6 June 2014

Albatross 2m sloper

Before the Red Sloper came this 2m wingspan sloper. It actually started life as a motor glider but a dodgy ESC connector stopped that project from being fully realised. I'll revisit it soon.

I call this one the Albatross for obvious reasons.

The orange plane is the pusher trainer with a 1.5m polyhedral no-aileron wing adapted from the slim wing. I'll post about that one when we get a nice calm day to do a proper maiden.

The depron I use comes in 1000mm x 700mm sheets so I can make the 2m wing in 2 halves.

I used 3 Skyshark spars all up, 2 joined with a 10mm x 150mm ali tube for the main spar and another spanning the join closer to the leading edge. The spar layout is visible in this shot of the wing on an earlier version of the fuselage.

The wing has full span ailerons operated by TGY 9018MG metal gear micro servos. Total chord is 200mm including the 35mm ailerons. That gives a 10:1 aspect ratio.

I suspect 40 to 45mm ailerons would have been better to give a faster roll rate for some aerobatics but they are fine for smooth cruising.

Airfoil thickness is 23mm, formed by using a 3mm strip of depron over the main spar, giving an 11.5% airfoil.

The tail is just a little scaled up from the Red Sloper but basically the same shape.

Horizonal stab is 460mm wide x 90mm deep tapered to 70mm at the ends plus a 50mm elevator.

Vertical stab is 220mm high x 130mm at the base tapered to 60mm at the top plus a 50mm rudder.

Elevator servo, hidden inside the fuselage, is a TGY 9018MG and rudder servo is HXT 900.

Fuselage is a 1000mm long x 70mm square tube tapered towards both ends for looks, weight saving and aerodynamics.

Weight is 650g without battery and balance weights and 830g flying weight.








The big wing makes for an excellent light wind slope soarer which also works well in strong winds. It's smooth and languid in the air, not so aerobatic, but a delight to cruise along the ridge.


UPDATE: I made the nose removable so I could swap to a motor pod. Just have to pull off the tape around the join and re-tape the motor pod on. The motor glider version is 730g without battery and 925g flying weight.

It took some decalage adjustment to smooth out the tendency to loop up under power. I needed to tilt the wing forward by sticking about 8mm of packing under the rear mounting area. Then it tracked level and glided much better.



Thursday, 29 May 2014

Red Sloper


Here are the specs for the Red Sloper fuselage, designed and built especially for the 1.5m depron 10% chord wing detailed in the previous post. 

Aileron servos - TGY 9018MG metal gear micros
Elevator and rudder servos - HXT900 9g
Receiver - Hobby King 6ch
BEC - Hobby King 5A

The 750mm fuselage is a square tube 50 x 50mm outer size constructed using Flite Test style joins rather than ExAir style bends. 

A 15mm x 350mm tapered slice is removed from each side, and the bottom bent up and re-glued to close the gap. That gives the tapered rear half.


Horizontal stabiliser is 440mm x 130mm, tapered to 100mm at the ends, and the 50mm elevator is cut from that. 




Vertical stabiliser is 200mm high, 120mm at the base (for a longer glue join) tapered to 40mm at the top. Rudder is 50mm tapering to 20mm at the top. 

The control surface tapers are just for looks, but looks are very important. A daggy tail ruins the overall impression of the plane.

Elevator servo is stuck inside the fuselage near the rudder servo. 

There is no need to have the tail servos mounted forward with long push rods. The amount of weight saving is not significant for a speedy slope soarer. In my normal 10-15kn flying conditions more weight is often needed.

The nose is soft EPP foam with a tongue extending into the fuselage. It holds the battery, nose weight (4 large washers), BEC and receiver. 

Nose is held on with 2 velcro tabs.





Wing tie-downs are 4mm carbon tubes glued in and reinforced with ID card plastic 



Here's the maiden flight of this excellent glider, probably my best design and build so far.


Tuesday, 20 May 2014

Better airfoil wing build

Following on from the Bending Better Depron Airoils article, this is the complete wing build.


It's basically an Experimental Airlines Armin wing with a few tweaks for the 6mm paperless foamboard and a nicely shaped airfoil. I'll mainly cover the steps that differ from Ed's instructions so check out his superior videos for more in-depth coverage.
This wing will be 1500mm (59") wingspan made from two 750mm (29 1/2") halves, joined with a 7.6mm Skyshark P4X wrapped carbon fibre tube spar. 

Airfoil section design
% thickness
I wanted a speedy slope soarer so Max thickness will be a slim 10% of total chord.
Using the information from my previous tests:
No extra former on top of the spar = 19mm thick airfoil, so a total chord of 190mm gives a 10% section.
3mm former on top of the spar = 23mm thick airfoil, so a total chord of 230mm gives a 10% section.
6mm former on top of the spar = 26mm thick airfoil, so a total chord of 260mm gives a 10% section.
For this wing I decided on the narrowest option - 19mm thick x 190mm chord section.

Max thickness location
30% back from the leading edge is what I'm aiming for and ailerons are included in the total chord measurement. 30% of 190mm = 57mm, so the spar will be positioned 57mm back from the leading edge.

Aileron size
40mm ailerons give sufficient stiffness and some aerobatic performance so now we have the overall airfoil dimensions.
Total chord = 190mm with a 150mm main airfoil and 40mm ailerons. Thats roughly a 6" main wing section with 1.5" ailerons giving 7.5" total chord.

Wing build
For this 190mm chord airfoil we need 150mm for the bottom surface, 150mm for the top surface, 40mm for the ailerons PLUS 10mm extra for the leading edge bend. That gives 150 + 150 + 40 + 10 = 350mm



Cut out the wing panels - two 350mm x 750mm rectangles

Cover one side with packing tape and use a plastic gift card edge to smooth it down. Watch Ed's tape covering video for complete instructions.

 Mark the leading edge fold line 150mm in from one of the long edges.

Draw a line 25mm in from the same edge for the bottom layer bevel.

Draw a line along the edge 2mm up from the taped surface. The idea is to leave a bit of thickness here so that the sub-trailing edge ends up 8mm thick. This allows the ailerons to form part of the overall airfoil shape.

Slice and sand the bevel back to the marked lines.

The finished bevel with 2mm thickness left at the sub-trailing edge. 

Make a dent along the leading edge fold line. I'm using my specially designed tool, a rounded off piece of 10mm dowell. I want a reasonably sharp leading edge so I'm making a deepish dent here, maybe 3/4 of the way through. This is the only dent I make, the slimmer airfoil section means the depron doesn't have to curve too much over the top, so kinking is not a problem. 

Clamp down a stiff ruler at the fold line and, using another full length piece of something stiff, bend the depron up to 90 degrees.

Remove the ruler and bend the depron right over, squashing down hard on the leading edge.

Mark the spar position. 30% back from the leading edge is 57mm for this wing. 

Position the spar and formers and mark the positions. The formers are 20mm wide and only one layer with nothing on top of the spar for this wing.

Glue the formers to the bottom layer then apply glue along the top.

Fold the top layer over and hold down to set with a long stiff ruler.
Depending on how hard you push down, more or less bottom curve will be formed. For a flat bottomed wing push down hard on the leading and trailing edges. For a more symmetrical airfoil you can let the leading edge curve up a little. As there is no paper to stiffen the bottom layer, depron naturally tends to produce some bottom curve.

Squirt glue into the sub-trailing edge join and clamp down to set. Again you can decide how much bottom curve you want by holding it down flat or letting it lift up a bit.

To finish the ailerons score down the sub-trailing edge but dont go right through to the tape.

Crack the aileron hinge free over a straight edge then slice off a 45 degree bevel and sand smooth to allow the aileron to swing down. 

Slice off the aileron trailing edge bevel and sand smooth. I draw a line 20mm in and bevel back to that and all the way down to the tape on the trailing edge. 

Here's it is just about done. See how the aileron forms part of the overall airfoil shape, very nice.

Add more tape to form the aileron hinge and make a sharp trailing edge. Check out Ed's Kissing tape technique for more detail.

To finish the wing completely, tape over the open outer ends, fit servos and control horns then tape the two halves together. As this wing has a curved bottom it may not sit flat on the fuselage. Some packing under the leading and trailing edges may be needed to hold it level.

Tape on two icypole sticks where the rubber bands pass over the wing edges.

I'll make another fuselage to match this wing but this one will do for the moment.

1.5m depron wing build video

Maiden flight


Links for materials and information
Experimental Airlines for designs and techniques
Tradewarehouse for bulk depron
Kitesandfunthings for CF spars
My website for underwater photography, kite aerial photography and RC flight

Friday, 2 May 2014

Better airfoils using 6mm depron

After the poor performance of my first 2m motor glider and great performance of the slim wing and symmetrical wing I though it was time to investigate airfoils more thoroughly.

My standard building materials are 6mm depron and 7.5mm Skyshark P4X spars while Experimental Airlines and Flite Test use 5mm Dollar Tree foam so I needed to tweak their methods for my designs.

For inspiration I looked at the Bixler 2 wing which glides beautifully, and the widely used Clark Y airfoil.

The key features are ... maximum thickness is around 11.7% of the total chord and positioned 30% back from the leading edge.

My mission was to come up with a technique to replicate these features using my materials.




Wing section construction

My standard wing building method is to cover one side of the 6mm depron with packing tape. I have used PPS and Scotch tapes and prefer the cheaper PPS.

The inside of the bottom trailing edge is tapered to 1" to conform with the top layer for gluing. I found it was better not to sand all the way down to the covering tape but to leave about 2mm thickness at the trailing edge. This allows the aileron to better blend in to the overall airfoil shape.

I make a slight dent line (with the other end of a pencil) along the inside of the leading edge position to give an accurate fold. Don't make the dent too deep or you will have a sharp leading edge.


I made up airfoil sections ranging in chord length (including ailerons) from 6.5" to 9.5", spar placement 20 to 30% back from the leading edge line with 20mm formers glued either side, and zero, half or a full thickness former on top of the spar.


The combinations that most closely matched the Clark Y airfoil were:

A. 7.0" chord (5.5" plus 1.5" aileron) Spar 53mm back with no extra former
B. 8.0" chord (6.5" plus 1.5" aileron) Spar 61mm back with an extra 3mm former layer
C. 9.5" chord (7.5 plus 2" aileron) Spar 76mm back with an extra 6mm former layer

To my eye these sections looked much nicer than my previous builds and much closer to commercially produced RC gliders and planes. Depron will kink rather than bend smoothly over the formers if the curve is too great but it's not a problem with these slimmer sections.

These have become my standard wing chord designs now. I would add larger 2" ailerons for aerobatic models, especially slope soarers. Varying degrees of airfoil section symmetry can be built-in by varying how much you press the wing down flat while gluing up.

A symmetrical section gives better inverted and aerobatic performance while a flat bottomed section gives more lift and better gliding performance.

I used the B section in my next project, the wonderful 2m slope soarer.

Monday, 21 April 2014

Symmetrical Armin wing slope soarer

This symmetrical Armin wing was designed specifically for aerobatic slope soaring. After two frustrating weeks of bad winds I finally got the chance to test it.

1.4m wingspan
20mm thick
140mm (5.5") chord plus 50mm (2") ailerons





Here's the proper maiden flight in 10-15kn NW. The wind was slightly off slope to the left but the glider behaved beautifully, a delight to fly and aerobatics worked nicely. Inverted flight was excellent, rolls and loops worked well too. It's quite a light weight at 480g and needed some ballast from a bigger battery when the wind picked up.



A few days ago in desperation I tossed it off the dune in 30kn and it did fly but exhibited some frightening elevator flutter. That flight was more survival than flying so it didn't count as the maiden.
The large aerobatic elevator with some area forward of the hinge contributed to the flutter, as well as sloppy linkages, short control arms, loose servo mount and a dodgy tape hinge.  The flutter only happened on launch into 30kn so it's not an issue in normal conditions.


Saturday, 19 April 2014

Pusher trainer and test body

I made this plane so that my brother and his kids could have a go at flying RC planes, and as a test body for comparing different wings.

Actually this is the rebuild of that original plane which served it's purpose well, for one very windy but fun day.

It's a "pusher", meaning the motor is not on the nose but pushes from behind the wing. That means nose-in crashes won't end the flying session.

The tail boom is a 7.5 mm woven carbon fibre tube and the main body a 100mm x 60mm box.

The box needs to be tall enough so the prop clears the boom.

The rudder must be tall enough to get some of the airflow coming across the top of the wing. With a shorter rudder I experienced significant adverse yaw and poor directional tracking. Might be better with a tapered fuselage.
Motor mount is aluminium flat, bent up just past 90ยบ and stuck on to a glued down ID card on top of the box.

Aileron servo lead extensions are taped to the rear sides of the box so wings can be easily swapped.








Multiple wing tie-down posts allow for different chord size wings to be mounted. The tie-down points are reinforced with pieces of ID card.

The tail boom is hot glued to the bottom of the body then depron strips glued either side of the tube for extra strength.






Tail servos are mounted on the tail.

I initially had the tail servos forward in the body with Gold-n-Rod push rods but these were chopped by the prop in a boom flexing hard landing.







The nose is soft parcel packing EPP covered in clear gaffer tape for impact absorbtion. It has an EPP tongue extending into the body to hold the battery. The battery can be moved right up into the nose or further back for balance.

I use this nose design in all my pusher and slope soarers now. Velcro tabs hold it in place.

Turnigy 2622/14 1450kV motor, 7x4.5 prop
500g without battery
Flying weight 610g with 1300mAh 3S

This video shows the maiden using a symmetrical 1.4m Armin wing