Here's a quick, cheap and easy vibration-damping camera mount using 2 cable ties and an ID card. It only takes a few minutes to make and greatly reduces those annoying jelly waves often seen in onboard video.
Tools needed are an office hole punch, scissors, side cutters and a marker pen. Materials needed are two small rubber bands, an ID card and two 4mm x 200mm cable ties.
Cut the card in half and punch 4 holes in each roughly 1cm in from the edges.
Double wrap the rubber bands on one card towards the middle from the holes.
Thread through the cable ties to form the springs. Start underneath and thread up out and around the card edges, then back through the bottom card into the middle. Continue on threading in and out the holes till you come back to the start.
Adjust the size of the loops until the top deck is level or possibly tilted forward a little.
Clip off the excess and it's done.
You still need to balance your props but this mount takes care of the vibrations that you can't fix.
Velcro on the bottom is a good way to attach the mount to a plane or even electrical tape for temporary positioning.
Here is the full build in real time - about 4 minutes.
This video shows the comparison of with and without the anti-vibe mount.
The twin boom configuration means the motor doesn't need to sit up high, which means the fuselage can be slimmer.
The forward swept wings give amazing anti-stall characteristics and increased grip in the turns. I suspect when the wing tips flex upward they give positive feedback to the turn, similar to snap flaps. A swept back wing would do the opposite. It also looks very cool in the air.
This plane can fly slow or fast and is crazy manoeuvrable even without movable rudders, and it can balance in it's tail.
The wing build is slightly different to my previous style, with cut out ailerons rather than full span. Wingspan is 1.3m or 53" compared to IBCrazy's 40" and 48" versions.
I made a 200mm (8") x 20mm flat bottomed airfoil in two 700mm halves, then cut a wedge from each inner end to make the forward sweep when glued and taped together. The tips are about 45mm forward of the root. I also cut wedges off the wingtips so they were parallel. Naturally I cut them the wrong way first.
I removed some of the forward former in the spar channel either side of the join so the Skyshark P4X spar had a wider bend curve.
UPDATE: Here are a two more recent Depron Spectre videos. Some aerobatics on a rare calm 13th Beach day and some slope soaring at Beacon Point in a lovely 10-15kn NW wind.
I have never tried a 3 channel rudder elevator throttle plane so thought I'd give it a go using the orange slim wing and pusher fuselage.
RET planes need some wing dihedral to enable turns due to the lack of ailerons.
I fixed the ailerons in place and removed the servos. This simplifies the plane greatly, the wing is just a wing, no servos or wires, apart from rudder and elevator.
The CF spar was removed and a bent 200mm x 10mm diam ali tube inserted to set the dihedral. The wing extensions were hot glued in place at the desired polyhedral angle. The wing seems to be strong enough without a CF spar.
I increased the rudder area, but after the maiden reduced the throws for smoother control.
The 1500mm x 200mm wing and flying weight of 630g gives a wing loading of about 21 g/sq dm (7oz/sq ft) which is great for gliding and slow flying.
This plane is a delight to fly, so slow and steady. If I had started with something like this the learning process would have been much quicker. I can trim it to fly hands off in big lazy circles and it takes care of itself.
Before the Red Sloper came this 2m wingspan sloper. It actually started life as a motor glider but a dodgy ESC connector stopped that project from being fully realised. I'll revisit it soon.
I call this one the Albatross for obvious reasons.
The orange plane is the pusher trainer with a 1.5m polyhedral no-aileron wing adapted from the slim wing. I'll post about that one when we get a nice calm day to do a proper maiden.
The depron I use comes in 1000mm x 700mm sheets so I can make the 2m wing in 2 halves.
I used 3 Skyshark spars all up, 2 joined with a 10mm x 150mm ali tube for the main spar and another spanning the join closer to the leading edge. The spar layout is visible in this shot of the wing on an earlier version of the fuselage.
The wing has full span ailerons operated by TGY 9018MG metal gear micro servos. Total chord is 200mm including the 35mm ailerons. That gives a 10:1 aspect ratio.
I suspect 40 to 45mm ailerons would have been better to give a faster roll rate for some aerobatics but they are fine for smooth cruising.
Airfoil thickness is 23mm, formed by using a 3mm strip of depron over the main spar, giving an 11.5% airfoil.
The tail is just a little scaled up from the Red Sloper but basically the same shape.
Horizonal stab is 460mm wide x 90mm deep tapered to 70mm at the ends plus a 50mm elevator.
Vertical stab is 220mm high x 130mm at the base tapered to 60mm at the top plus a 50mm rudder.
Elevator servo, hidden inside the fuselage, is a TGY 9018MG and rudder servo is HXT 900.
Fuselage is a 1000mm long x 70mm square tube tapered towards both ends for looks, weight saving and aerodynamics.
Weight is 650g without battery and balance weights and 830g flying weight.
The big wing makes for an excellent light wind slope soarer which also works well in strong winds. It's smooth and languid in the air, not so aerobatic, but a delight to cruise along the ridge.
UPDATE: I made the nose removable so I could swap to a motor pod. Just have to pull off the tape around the join and re-tape the motor pod on. The motor glider version is 730g without battery and 925g flying weight.
It took some decalage adjustment to smooth out the tendency to loop up under power. I needed to tilt the wing forward by sticking about 8mm of packing under the rear mounting area. Then it tracked level and glided much better.
Here are the specs for the Red Sloper fuselage, designed and built especially for the 1.5m depron 10% chord wing detailed in the previous post.
Aileron servos - TGY 9018MG metal gear micros
Elevator and rudder servos - HXT900 9g
Receiver - Hobby King 6ch
BEC - Hobby King 5A
The 750mm fuselage is a square tube 50 x 50mm outer size constructed using Flite Test style joins rather than ExAir style bends.
A 15mm x 350mm tapered slice is removed from each side, and the bottom bent up and re-glued to close the gap. That gives the tapered rear half.
Horizontal stabiliser is 440mm x 130mm, tapered to 100mm at the ends, and the 50mm elevator is cut from that.
Vertical stabiliser is 200mm high, 120mm at the base (for a longer glue join) tapered to 40mm at the top. Rudder is 50mm tapering to 20mm at the top.
The control surface tapers are just for looks, but looks are very important. A daggy tail ruins the overall impression of the plane.
Elevator servo is stuck inside the fuselage near the rudder servo.
There is no need to have the tail servos mounted forward with long push rods. The amount of weight saving is not significant for a speedy slope soarer. In my normal 10-15kn flying conditions more weight is often needed.
The nose is soft EPP foam with a tongue extending into the fuselage. It holds the battery, nose weight (4 large washers), BEC and receiver.
Nose is held on with 2 velcro tabs.
Wing tie-downs are 4mm carbon tubes glued in and reinforced with ID card plastic
Here's the maiden flight of this excellent glider, probably my best design and build so far.
It's basically an Experimental Airlines Armin wing with a few tweaks for the 6mm paperless foamboard and a nicely shaped airfoil. I'll mainly cover the steps that differ from Ed's instructions so check out his superior videos for more in-depth coverage.
This wing will be 1500mm (59") wingspan made from two 750mm (29 1/2") halves, joined with a 7.6mm Skyshark P4X wrapped carbon fibre tube spar.
Airfoil section design
% thickness
I wanted a speedy slope soarer so Max thickness will be a slim 10% of total chord.
Using the information from my previous tests:
No extra former on top of the spar = 19mm thick airfoil, so a total chord of 190mm gives a 10% section.
3mm former on top of the spar = 23mm thick airfoil, so a total chord of 230mm gives a 10% section.
6mm former on top of the spar = 26mm thick airfoil, so a total chord of 260mm gives a 10% section.
For this wing I decided on the narrowest option - 19mm thick x 190mm chord section.
Max thickness location
30% back from the leading edge is what I'm aiming for and ailerons are included in the total chord measurement. 30% of 190mm = 57mm, so the spar will be positioned 57mm back from the leading edge.
Aileron size
40mm ailerons give sufficient stiffness and some aerobatic performance so now we have the overall airfoil dimensions.
Total chord = 190mm with a 150mm main airfoil and 40mm ailerons. Thats roughly a 6" main wing section with 1.5" ailerons giving 7.5" total chord.
Wing build
For this 190mm chord airfoil we need 150mm for the bottom surface, 150mm for the top surface, 40mm for the ailerons PLUS 10mm extra for the leading edge bend. That gives 150 + 150 + 40 + 10 = 350mm
Cut out the wing panels - two 350mm x 750mm rectangles
Cover one side with packing tape and use a plastic gift card edge to smooth it down. Watch Ed's tape covering video for complete instructions.
Mark the leading edge fold line 150mm in from one of the long edges.
Draw a line 25mm in from the same edge for the bottom layer bevel.
Draw a line along the edge 2mm up from the taped surface. The idea is to leave a bit of thickness here so that the sub-trailing edge ends up 8mm thick. This allows the ailerons to form part of the overall airfoil shape.
Slice and sand the bevel back to the marked lines.
The finished bevel with 2mm thickness left at the sub-trailing edge.
Make a dent along the leading edge fold line. I'm using my specially designed tool, a rounded off piece of 10mm dowell. I want a reasonably sharp leading edge so I'm making a deepish dent here, maybe 3/4 of the way through. This is the only dent I make, the slimmer airfoil section means the depron doesn't have to curve too much over the top, so kinking is not a problem.
Clamp down a stiff ruler at the fold line and, using another full length piece of something stiff, bend the depron up to 90 degrees.
Remove the ruler and bend the depron right over, squashing down hard on the leading edge.
Mark the spar position. 30% back from the leading edge is 57mm for this wing.
Position the spar and formers and mark the positions. The formers are 20mm wide and only one layer with nothing on top of the spar for this wing.
Glue the formers to the bottom layer then apply glue along the top.
Fold the top layer over and hold down to set with a long stiff ruler.
Depending on how hard you push down, more or less bottom curve will be formed. For a flat bottomed wing push down hard on the leading and trailing edges. For a more symmetrical airfoil you can let the leading edge curve up a little. As there is no paper to stiffen the bottom layer, depron naturally tends to produce some bottom curve.
Squirt glue into the sub-trailing edge join and clamp down to set. Again you can decide how much bottom curve you want by holding it down flat or letting it lift up a bit.
To finish the ailerons score down the sub-trailing edge but dont go right through to the tape.
Crack the aileron hinge free over a straight edge then slice off a 45 degree bevel and sand smooth to allow the aileron to swing down.
Slice off the aileron trailing edge bevel and sand smooth. I draw a line 20mm in and bevel back to that and all the way down to the tape on the trailing edge.
Here's it is just about done. See how the aileron forms part of the overall airfoil shape, very nice.
Add more tape to form the aileron hinge and make a sharp trailing edge. Check out Ed's Kissing tape technique for more detail.
To finish the wing completely, tape over the open outer ends, fit servos and control horns then tape the two halves together. As this wing has a curved bottom it may not sit flat on the fuselage. Some packing under the leading and trailing edges may be needed to hold it level.
Tape on two icypole sticks where the rubber bands pass over the wing edges.
I'll make another fuselage to match this wing but this one will do for the moment.